Motorbike & Motorcycle Battery Charger Scooter & moped Battery Charger Vintage Motorcycle 6 Volt Battery Charger Snowmobile Battery Charger Watercraft Battery Charger ATV & Four Wheeler Battery Charger Car Battery Charger Vintage Car Battery Charger Caravan and RV Battery Charger Gardening and Lawnmower Battery Charger Motor Boat Battery Charger Sailing Boat Battery Charger

Battery Charger Installation

Battery Connector with Eyelets - STD2V - Installation Procedure

The following operations are necessary for a correct set-up of the device. Please note the recommended cables configuration (STD2V cable always on-board and connected to the battery poles) allows you to perform this procedure just once.
The user is kindly requested to execute the installation with maximum care (see Directions and Safety section on the manual). If necessary, please entrust qualified personnel with the execution of the steps reported here below:

  1. Connect the cable STD2V to the battery: connect the black wire to the (-) negative Battery pole, the red wire to the (+) positive battery pole.

Moreover, in order to ensure a regular functioning, it is suggested to periodically check the correct and stable connection of the eyelets to the Battery and the removal of eventual dust and oil from poles with a metallic brush.

-----------------------------------------------------------------------------

Battery Charger Installation Procedure

  1. Connect the device (off state) to the 220V power outlet.
  2. Verify that the battery charger is on (LCD display or red LED on, signaling that the battery is not connected).
  3. Remove the connector saver cap from the STD2V battery cable and connect the battery charger to the battery cable. Alternatively, connect the battery charger to the cigar socket through ACC612V (Universal Cigar Socket Adapter) or directly to the battery poles through 30AMPPZ (Battery Connector with Clamps).

Once connected, the battery charger will start the charging cycle.

-----------------------------------------------------------------------------

Battery Charger Disconnection Procedure

  1. Disconnect the device from the 220V power outlet.
  2. Disconnect the device from the battery cable with eyelets (or clamps, or cigar socket adapter).
  3. Restore the connector saver cap on the STD2V battery cable connector.
  4. Put the battery cable cable back in its hiding place.
  5. Put the battery charger back in its box to minimise its exposure to the atmospheric agents.
BC BATTERY CHARGERS
FOR HOME BATTERY CARE
BC BATTERY CHARGERS
FOR LEAD-ACID BATTERIES (WET, GEL,
MF, AGM...) AND LITHIUM BATTERIES
BC DUETTO BC K900 EVO
12V 1.5 AMP CAN-BUS
Lead-Acid/Lithium Battery Charger BC DUETTO Battery charger and maintainer BC K900 EVO
BC BATTERY CHARGERS
FOR LEAD-ACID BATTERIES
(WET, GEL, MF, AGM, VRLA...)
CAR/BIKE BATTERY CHARGERS
BC JUNIOR 900 BC K612
BC JUNIOR 900 battery charger and maintainer BC K612 battery charger for 6V and 12V batteries
BC SMART 2000 BC BRAVO 2000
BC SMART battery charger and maintainer BC BRAVO battery charger and tester
BC K900 edge BC PLUS
6/12V CAN-BUS 4000 24V
BC K900 edge - 6/12V battery charger and maintainer BC PLUS 4000 24V battery charger and maintainer
BC 9000 EVO BC 3500 EVO
BC 9000 EVO battery charger and tester BC 3500 EVO battery charger and tester
BC SMART 5000 BC SMART 10000
Battery charger and maintainer BC SMART 5000 Battery charger and maintainer BC SMART 10000
BC LITHIUM CHARGERS
FOR LITHIUM LiFePO4 BATTERIES
BC LITHIUM 1500 BC LITHIUM 7000
LiFePO4 battery charger BC LITHIUM 1500 LiFePO4 battery charger and tester BC LITHIUM 7000
PROFESSIONAL BATTERY CARE
BC Pro 4S BT-02
BC Pro 4S - Professional battery charger with 4 units BT02 battery and alternator tester
Portable jump starter BC Booster K1200
PRIVATE USERS
Select the right battery charger
- for your motorcycle >>
- for your car >>
- for your battery >>
 
Where to buy >>
Information Request >>
F.A.Q. - Frequently Asked Questions >>
PROFESSIONAL USERS
Join BC Distribution Network >>
Find BC Distributors in your Country >>
BC Pro Series - Professional
Battery Chargers & Testers
- BC Pro 4S - Professional Charger for Lead-Acid and Lithium Batteries >>
- BT02 6/12V Battery Test 40-2000 CCA
  + 12/24V Charging System Test >>

- Accessories >>
FAIRS AND EXIBITIONS
EICMA 2017 - November 07-12 - Milan - Hall 13 Stand S-64
Automechanika Birmingham 2017 - June 6-8 - NEC Birmingham - Stand 20G98
AUTOPROMOTEC 2017 - May 24-28 - Bologna - Hall 36 Stand E7
TICINO MOTOR EXPO 2017 - April 08-09 - Lugano - TTS
EXPOMECANICA 2017 - April 07-09 - Porto - Leatronic - Hall 6
Motopassion 2017 - March 24-April 2 - Belgrade - Motomania d.o.o.
MOTO DAYS 2017 - March 09-12 - Rome
IRISH MOTORBIKE & SCOOTER SHOW 2017 - March 03-05 - Dublin
MP17 MOTORCYCLE SHOW - February 03-05 - 2017 - Helsinki
MOTORCYCLE TRADE EXPO 2017 - January 15-17 - Coventry
EICMA 2016 - November 08-13 - Milan
INTERMOT 2016 - October 05-09 - Cologne
Automechanika 2016 - September 13-17 - Frankfurt
PRESS
Company Profile
Home  |  Company  |  Contact Us  |  Site Map