 |
      |
|
BC Plus 4000 is the new smart battery charger designed for the maintenance of all 24V batteries, with microprocessor and Liquid Crystal Display. With the introduction of this model in BC range of chargers, the innovative 8-steps charging algorithm developed by BC Battery Controller is now available also for all vans, boats and trucks batteries.
BC Plus 4000 is ideal for the recovery, charge, desulfation, maintainance and analysis of all 24V batteries and it can be left always connected to the battery, with no risk and no need to disconnect |
|
the battery from the vehicle, keeping it fully charged during long periods of inactivity (even months).
The charger delivers a maximum current of 4 Amps and runs a fully automatic 8-cycles charging algorithm, providing a complete solution to recover deep discharged batteries (from 3 volts) and to recharge, desulphate and maintain all 24V batteries (traditional, gel, sealed...) from 15 to 80 Ah (up to 150 Ah for maintenance).
The display shows the charging cycle executed, any functioning error as well as the battery state of charge (digital |
|
voltmeter) in real time.
BC Plus 4000 does not produce sparks and it is protected against short circuit, reverse polarity, overcharging and overheating.
The package includes a waterproof battery cable with eyelets (code STD2V), which can be left always installed on the vehicle, and a battery cable with insulated clamps (code 30AMPPZ). The warranty is extended to 3 years.
| |
 |
| TECHNICAL DATA |
BC PLUS 4000 |
| Input Voltage |
220÷240 Vac, 50÷60 Hz |
| Charge Voltage |
27.6 V / 28.8 V - nominal 24 V |
| Charge Current |
4.0 A max |
| Charging Algorithm |
8 cycles, automatic (Initialization, Recovery,
Soft Charge, Bulk Charge, Desulfation,
Battery Analysis, Maintenance and Equalization) |
| Types of Batteries |
24 V Lead Acid
(Traditional, Gel, MF, VRLA, AGM, etc.) |
| Battery Capacity |
From 15 Ah to 80 Ah (Charge),
up to 150 Ah (Maintenance) |
| Operating Temperature |
from 0° to +50° C | |
Featuring wall mounting system
with fast dismounting
|
DOWNLOAD
PRODUCT SHEETS
     |
MANUALS
|
FOLDERS
| |
|
8 CYCLES CHARGING TECHNOLOGY
BC PLUS 4000 is a digital 24V battery charger and maintainer managed by a latest-generation microprocessor, which is in charge of monitoring the battery parameters in real time and to execute a new multi-cycle charging algorithm:
1. Initialization: the device checks if one or more cells are shorted, in order to verify that the battery is in a proper condition to be recharged/recovered.
2. Recovery: if the battery is deep discharged (battery voltage starting from 1.5 V), the device tries to recover it, taking it back to a higher voltage.
3. Soft Charge: if the battery is in a condition of significant undercharge, the device provides a light pulsing current to the battery, to overcome this critical phase.
4. Bulk Charge: the device provides full current to the battery, recovering about 85-90% of the battery capacity.
5. Desulfation / Absorption: the device provides a "controlled overcharge" to recover the remaining 10-15% of the battery capacity, through the desulfation/recovery the lead-acid cells (for low or medium sulfation).
6. Battery Analysis - End Cycle Test: the device stops providing current to the battery for a short time, in order to verify whether the battery is able to retain the charge received. This test is periodically repeated during the Maintenance.
7. Maintenance: the device keeps the battery in the best charge conditions for very long periods (even months) during which your vehicle is left unused, without any possible drawback (battery overcharge, battery overheating, water and/or electrolyte loss, etc).
8. Equalization: every 30 days during long term maintenance, the device executes an equalization charge in order to balance the battery lead-acid cells, avoiding electrolyte stratification within the cells.
SAFETY AND PROTECTIONS
BC PLUS 4000 features a series of 8 protections and active guard mechanisms that make it easy to install and to use, without any risks even for users without expertise:
No interferences the vehicle's on board electronics (control unit, ABS, GPS...)
Protection from output lines short circuit, even for an indefinite time: no sparks!
Protection from battery polarity inversion
Protection from battery overcharge/overheating
Thermal protection from overtemperature
No need to disconnect the battery from your vehicle
Very few gas development during the charge: no need to remove the battery plugs
Laboratory Tests ensure the manufacturing of products in conformity to the regulations in force on safety and electro-magnetic compatibility. Norms and Regulations: EN55014-1, EN55014-2, EN60335-1, EN60335-2-29, EN61000-3-2, EN61000-3-3.
BATTERY TYPES AND CAPACITY
BC PLUS 4000 is specifically designed for charging and maintaining all 24V lead-acid batteries currently available on the market (traditional, VRLA, MF, AGM, GEL, etc). BC PLUS 4000 is addressed to recharge batteries with a capacity from 15 to 80 Ah (up to 150 Ah for Maintenance only).
EQUIPMENT & ADD-ONS
The package includes:
the battery charger and maintainer BC PLUS 4000 for long term battery maintenance, provided with a 220V power cable (2 meters long) and a battery output cable;
STD2V waterproof battery cable with eyelets, which can be left always installed on board;
30AMPPZ battery cable with clamps;
a copy of the User Manual.
| | |
|
|
|
All the Battery Chargers and Accessories BC Battery Controller are developed and manufactured by Forelettronica srl. BC Battery Controller is a Registered Trademark.